Digi ConnectPort X4 - 802.15.4 Guía de usuario Pagina 129
- Pagina / 254
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuration through the web interface
129
Basic and Advanced radio settings
The Basic radio settings control basic operation of the XBee module in an XBee network.
Advanced radio settings control behavior of the XBee module at a more detailed level. Generally,
these settings can be left at their defaults.
For complete settings and descriptions of these options, refer to the Product Manual for the XBee
or XBee-PRO RF module in your product.
View and change configuration settings as needed. To apply configuration changes, click Apply.
Note
Changing the PAN ID may make your XBee product inaccessible.
If you assign a Node Identifier, to view it, go to Configuration > XBee Network and
click Refresh. The new name is displayed in the Node Identifier field.
Firmware updates for XBee modules
XBee RF modules can be updated with new firmware over the XBee network. Firmware updates
can be made both to the XBee RF module in the Digi device serving as a gateway to the XBee
network, and to the XBee RF modules in other XBee network nodes.
Firmware updates for the ConnectPort X gateway’s XBee module are available through
Digi Technical Support. Once loaded onto a PC, firmware updates can be loaded into the XBee
module by several methods:
In the web interface for the ConnectPort X gateway, by clicking the
Firmware Update Setup link on the XBee Network Configuration page and
uploading files containing the new firmware. Multiple files may be uploaded, each
containing a different firmware type.
Firmware updates of network nodes can be scheduled and monitored on the
Firmware Update Status page.
Through the command line interface, using several options on the set xbee command.
Note
XBee firmware can also be updated by sending over-the-air (OTA) commands to the
XBee module through the OTA graphical user interface of X-CTU, a software tool for
configuring XBee modules. In X-CTU, the OTA interface is called
Remote Configuration. However, the Enable over the air firmware updates
setting on the Firmware Update Setup page enables remote firmware updates
without having to use X-CTU.
XBee Firmware requirements
The XBee firmware version must be compatible with the XBee module’s hardware and the
ConnectPort X gateway firmware.
The XBee firmware must also be over-the-air compatible with other nodes. Generally, this means
that the gateway and nodes must be the same network type (ZB, 802.15.4, etc.) and have the same
or similar firmware version.
- ConnectPort™ X Family 1
- User’s Guide 1
- Contents 3
- About this guide 7
- Digi contact information 8
- Introduction 9
- ConnectPort X Family products 10
- Features 11
- Hardware features 18
- Network interface features 18
- Configurable network services 18
- IP protocol support 19
- RealPort software 24
- Modem emulation 24
- Configuration management 26
- Customization capabilities 26
- Network services 27
- Network/serial clients 29
- Configuration capabilities 30
- Configuration interfaces 30
- Network Status 36
- Mobile connection status 36
- Device administration 37
- Hardware 38
- Connector pinouts 39
- Cable fittings 42
- ConnectPort 43
- SIM card slots 44
- Power cable fitting 45
- Optional Ethernet hub feature 46
- Configure Digi devices 47
- Open the web interface 52
- Discover devices 53
- WEP Keys 62
- #> telnet digi16 2101 68
- Caution 75
- General Security Settings 85
- Miscellaneous Settings 85
- Local Endpoint Type: 86
- VPN Mode: 86
- Identity settings 86
- Local Endpoint: 87
- Pre-Shared Key Settings 87
- ISAKMP Phase 1 Settings 88
- Cellular 90
- Data Network 90
- Internet 90
- Remote Site HQ 90
- 5 Click Apply 94
- Local Name: A phone number 95
- Static Primary DNS 97
- Mobile (cellular) settings 103
- 5 Provisioning complete 108
- Enable 118
- Password 118
- Notes for the table: 120
- Supported character set 121
- XBee network settings 127
- Update Settings section 134
- 3 Click the Update button 136
- Serial port settings 137
- Camera settings 145
- System settings 150
- Authentication failure 155
- Cold start 155
- Link up 155
- Mobile (Cellular) Settings: 161
- 4 Click Apply 163
- Security settings 164
- Position (GPS support) 168
- Applications 170
- Digi device 173
- Digi device and click Delete 173
- RealPort Settings 174
- Device Descriptors: 176
- Access the command line 178
- Monitor and manage Digi 182
- Monitor/manage XBee networks 183
- Display system information 184
- Diagnostics 201
- View DHCP server status 203
- Digi device administration 210
- File management 211
- Trusted Peer Certificates 214
- 3 Click Update 216
- 4 Click Restore 217
- Connector 218
- Reboot the Digi device 220
- Specifications and 222
- Hardware specifications 223
- ConnectPort X4 specifications 225
- ConnectPort X8 specifications 227
- Wireless networking features 228
- Safety statements 232
- ConnectPort X4 S2 2G Term 233
- ConnectPort X4 H 233
- Troubleshooting 235
- System status LEDs 236
- ConnectPort X4 - Top 238
- ConnectPort X4 - Front panel 238
- ONNECT ORT 239
- Glossary 245
Relacionado con productos y manuales para Gateways / Controladores Digi ConnectPort X4 - 802.15.4
(95 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.238 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales