Digi DC-ES-8SB Guía de usuario Pagina 154
- Pagina / 195
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Administration from the web interface
154
Update firmware and Boot/POST Code
The firmware and/or boot/POST code for a Digi device can be updated from a file on a PC or
through TFTP. The recommended method is to download the firmware to a local hard drive. TFTP
is supported for those using UNIX systems. Both the firmware and the boot/POST code are
updated using the same set of steps.The Digi device automatically determines the type of image
being uploaded. Before uploading the firmware or the boot/POST code, it is very important to read
the Release Notes supplied with the firmware to check if the boot/POST code must be updated
before updating the firmware.
Prerequisites
These procedures assume that:
A firmware file has already been downloaded from digi.com.
If using TFTP, that the TFTP server is running.
Update firmware from a file on a PC
1 From the Main menu, click Administration > Update Firmware. The Update Firmware
page is displayed.
2 Enter the name of the firmware or POST file in the Select Firmware edit box, or click
Browse to locate and select the firmware or POST file.
3 Click Update.
Important: DO NOT close the browser until the update is complete and a reboot
prompt has been displayed.
Update Firmware from a TFTP Server
Updating firmware from a TFTP server is done from the command-line interface using the boot
command. It cannot be done from the web interface. For details, see "Administration from the
command-line interface" on page 161.
- Digi Connect 1
- Family and 1
- ConnectPort 1
- TS Family 1
- User’s Guide 1
- Contents 3
- About this guide 7
- Digi contact information 8
- Introduction 9
- The Digi Connect 10
- Digi Connect Wi-ME 11
- Digi Connect EM 11
- Digi Connect Wi-EM 11
- ConnectPort 12
- TS products 12
- ConnectPort TS 4x4 products 12
- Features 13
- IP protocol support 14
- Point-to-Point Protocol (PPP) 17
- RealPort software 18
- Modem emulation 19
- Encryption 20
- Configuration management 21
- Customization capabilities 21
- Network services 22
- Network/serial clients 24
- Configuration capabilities 25
- Configuration interfaces 26
- Digi Device Discovery utility 28
- Device Management™ interface 29
- Web interface 31
- Java applet interface 32
- Command-line interface 34
- Device Management 36
- Hardware 38
- Installation 39
- Physical location and spacing 40
- Temperature 40
- Power and wiring: 40
- Configuration 41
- IP address assignment 42
- Discover the device 46
- Port profiles 46
- Verify configuration settings 47
- Save settings 47
- Open the web interface 48
- Ethernet IP settings 56
- Ethernet Switch IP Settings 56
- WiFi IP settings 60
- WiFi LAN settings 60
- WiFi security settings 61
- WEP Keys 62
- Network services settings 64
- IP filtering settings 67
- IP forwarding settings 68
- Socket tunnel settings 71
- Advanced network settings 72
- Serial port settings 74
- RealPort profile 75
- Console Management profile 75
- TCP Sockets profile 76
- When the TCP 76
- UDP Sockets profile 77
- Serial Bridge profile 77
- Local Configuration profile 77
- Modem Emulation profile 78
- Industrial Automation profile 78
- Dialserv Profile 78
- Custom Profile 78
- Basic serial settings 79
- Advanced serial settings 80
- Test GPIO pins 84
- Alarm notification settings 85
- Alarm conditions 86
- Alarm configuration 87
- Enable and Disable Alarms 88
- System settings 89
- Date and Time settings 90
- Authentication failure 95
- Cold start 95
- Link up 95
- Device Cloud settings 97
- Connection settings 98
- Mobile (Cellular) Settings: 102
- 4 Click Apply 104
- Users settings 105
- Caution 106
- Password authentication 107
- Add users 109
- User access settings 109
- User permissions settings 110
- 3 Click on User Permissions 111
- 5 Click Apply 111
- Applications 113
- Digi device 115
- Digi device and click Delete 115
- RealPort Settings 118
- Ekahau Client™ 119
- Device Descriptors: 120
- Select COM1 and click OK 123
- Down/Off 124
- System requirements 125
- The Home page 126
- Restoring settings 127
- Network settings 128
- Serial ports 128
- GPIO pins 128
- Security features 129
- Access the command line 130
- Monitoring and management 134
- Display system information 136
- General system information 137
- GPIO information 137
- Serial port information 138
- Network statistics 140
- ICMP statistics 142
- WiFi LAN statistics 143
- Device Cloud status 144
- Diagnostics 144
- Manage serial ports 145
- Manage connections 145
- Event logging 146
- Device administration 151
- File management 152
- Prerequisites 154
- Using the boot command 155
- Reset button 156
- Activate Find Me LED 158
- Reboot the Digi device 158
- Latency Tuning 162
- Specifications and 167
- 4 kV burst (EFT) 168
- 2 kV surge per EN61000-4-5 168
- RJ-45 Pinout 169
- Hardware specifications 170
- Wireless networking features 173
- Infrastructure Mode 174
- Ad-Hoc Mode 174
- RF exposure statement 175
- Modifications (FCC 15.21) 176
- Cables (FCC 15.27) 176
- Troubleshooting 179
- Digi Connect SP - Back 180
- Digi Connect Wi-SP - Back 181
- Digi Connect ME - Back 182
- Wi-Fi Activity 183
- Status LED 183
- Wi-Fi Link 183
- System status LEDs 184
- LED Behaviors 185
- Attention: 186
- Consult accompanying 186
- Dangerous Voltage 186
- ConnectPort TS 4x2 - Back 188
- ConnectPort TS 4x4 - Back 188
- ConnectPort TS W 190
- ConnectPort TS 16- Back Panel 194
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales