Digi DC-ES-8SB Guía de usuario Pagina 82
- Pagina / 195
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuration through the web interface
82
Close connection after the following number of idle seconds: Enable to close an idle
connection. Use the Timeout field to enter the number of seconds that the connection
will be idle before it is closed. This can be 1 to 65000 seconds.
Close connection when DCD goes low: When selected, the connection will be closed
when the DCD (Data Carrier Detected) signal goes low.
Close connection when DSR goes low: When selected, the connection will be closed
when the DSR (Data Set Ready) signal goes low.
UDP settings
The UDP Settings are displayed only when the current serial port is configured with the UDP
Sockets or the Custom Profile.
Send Socket ID: Include an optional identifier string with the data sent over the
network. The Socket ID can be 1 to 256 ASCII characters. To enter non-printable
characters, use these key sequences:
Display current serial port settings
To display the current serial port settings for a Digi device, enter the display techsupport
command from the command line interface.
Character Key Sequence
backspace \b
formfeed \f
tab \t
new line \n
return \r
backslash \\
hexadecimal values \xhh
- Digi Connect 1
- Family and 1
- ConnectPort 1
- TS Family 1
- User’s Guide 1
- Contents 3
- About this guide 7
- Digi contact information 8
- Introduction 9
- The Digi Connect 10
- Digi Connect Wi-ME 11
- Digi Connect EM 11
- Digi Connect Wi-EM 11
- ConnectPort 12
- TS products 12
- ConnectPort TS 4x4 products 12
- Features 13
- IP protocol support 14
- Point-to-Point Protocol (PPP) 17
- RealPort software 18
- Modem emulation 19
- Encryption 20
- Configuration management 21
- Customization capabilities 21
- Network services 22
- Network/serial clients 24
- Configuration capabilities 25
- Configuration interfaces 26
- Digi Device Discovery utility 28
- Device Management™ interface 29
- Web interface 31
- Java applet interface 32
- Command-line interface 34
- Device Management 36
- Hardware 38
- Installation 39
- Physical location and spacing 40
- Temperature 40
- Power and wiring: 40
- Configuration 41
- IP address assignment 42
- Discover the device 46
- Port profiles 46
- Verify configuration settings 47
- Save settings 47
- Open the web interface 48
- Ethernet IP settings 56
- Ethernet Switch IP Settings 56
- WiFi IP settings 60
- WiFi LAN settings 60
- WiFi security settings 61
- WEP Keys 62
- Network services settings 64
- IP filtering settings 67
- IP forwarding settings 68
- Socket tunnel settings 71
- Advanced network settings 72
- Serial port settings 74
- RealPort profile 75
- Console Management profile 75
- TCP Sockets profile 76
- When the TCP 76
- UDP Sockets profile 77
- Serial Bridge profile 77
- Local Configuration profile 77
- Modem Emulation profile 78
- Industrial Automation profile 78
- Dialserv Profile 78
- Custom Profile 78
- Basic serial settings 79
- Advanced serial settings 80
- Test GPIO pins 84
- Alarm notification settings 85
- Alarm conditions 86
- Alarm configuration 87
- Enable and Disable Alarms 88
- System settings 89
- Date and Time settings 90
- Authentication failure 95
- Cold start 95
- Link up 95
- Device Cloud settings 97
- Connection settings 98
- Mobile (Cellular) Settings: 102
- 4 Click Apply 104
- Users settings 105
- Caution 106
- Password authentication 107
- Add users 109
- User access settings 109
- User permissions settings 110
- 3 Click on User Permissions 111
- 5 Click Apply 111
- Applications 113
- Digi device 115
- Digi device and click Delete 115
- RealPort Settings 118
- Ekahau Client™ 119
- Device Descriptors: 120
- Select COM1 and click OK 123
- Down/Off 124
- System requirements 125
- The Home page 126
- Restoring settings 127
- Network settings 128
- Serial ports 128
- GPIO pins 128
- Security features 129
- Access the command line 130
- Monitoring and management 134
- Display system information 136
- General system information 137
- GPIO information 137
- Serial port information 138
- Network statistics 140
- ICMP statistics 142
- WiFi LAN statistics 143
- Device Cloud status 144
- Diagnostics 144
- Manage serial ports 145
- Manage connections 145
- Event logging 146
- Device administration 151
- File management 152
- Prerequisites 154
- Using the boot command 155
- Reset button 156
- Activate Find Me LED 158
- Reboot the Digi device 158
- Latency Tuning 162
- Specifications and 167
- 4 kV burst (EFT) 168
- 2 kV surge per EN61000-4-5 168
- RJ-45 Pinout 169
- Hardware specifications 170
- Wireless networking features 173
- Infrastructure Mode 174
- Ad-Hoc Mode 174
- RF exposure statement 175
- Modifications (FCC 15.21) 176
- Cables (FCC 15.27) 176
- Troubleshooting 179
- Digi Connect SP - Back 180
- Digi Connect Wi-SP - Back 181
- Digi Connect ME - Back 182
- Wi-Fi Activity 183
- Status LED 183
- Wi-Fi Link 183
- System status LEDs 184
- LED Behaviors 185
- Attention: 186
- Consult accompanying 186
- Dangerous Voltage 186
- ConnectPort TS 4x2 - Back 188
- ConnectPort TS 4x4 - Back 188
- ConnectPort TS W 190
- ConnectPort TS 16- Back Panel 194
© 2020, manymanuals.es. Todos los derechos reservados | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales