Digi ConnectPort X4 Guía de usuario Pagina 105
- Pagina / 271
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuration through the web interface
105
Mobile connection settings
Mobile connection settings configure how the mobile connection is established and maintained.
Re-establish connection when no data is received for a period of time:
Inactivity timeout: Whether the mobile connection will be disconnected and re-
established after no data has been received over the link for the specified amount of
time, in seconds.
SIM Selection settings
The following options control how the Digi device chooses a SIM card to establish mobile
connections.
The primary SIM will used first to try to establish a connection. If the connection is unsuccessful,
the secondary SIM will be used instead. If it is also unsuccessful, the primary and then secondary
SIMs will be tried again repeatedly.
Stop using this SIM and switch to the next SIM
These settings determine when a connection attempt is unsuccessful, at which point
the Digi device should switch to the next SIM card to establish mobile connections.
If this SIM is not registered after n seconds: The SIM has not registered with
the mobile service provider after a specified number of seconds.
If roaming with this SIM: The SIM is registered, but is roaming to another service
provider. Your provider may apply additional connection charges when roaming.
After n connection failures: A connection could not be established after the specified
number of attempts.
Disconnect this SIM and return to the primary SIM
Once a connection has been successfully established with this SIM, these settings determine when
to end the connection and return to using the primary SIM.
When the connection is dropped: The connection has ended for any reason.
If the connection is idle for n seconds: No data has been received over the mobile link
for the specified number of seconds.
After a maximum of n seconds: The connection has been established for the specified
number of seconds.
- ConnectPort 1
- X Family 1
- User’s Guide 1
- Contents 3
- About this guide 6
- Digi contact information 7
- Introduction 8
- X products 9
- Features 10
- IP protocol support 11
- Provisioning wizard 15
- Digi SureLink™ 15
- Mobile/Cellular protocols 15
- RealPort software 16
- Modem emulation 17
- Encryption 18
- Configuration management 19
- Customization capabilities 19
- Network services 20
- Network/serial clients 22
- Configuration capabilities 23
- Configuration interfaces 24
- Digi Device Discovery utility 25
- Device Manager™ interface 26
- Web interface 28
- Command-line interface 29
- Device Manager 31
- Hardware 33
- Connector pinouts 34
- 4 analog I/O 37
- 4 digital I/O 37
- Cable fittings 39
- SIM card slots 40
- Power cable fitting 41
- Optional Ethernet hub feature 42
- Configuration 43
- IP address assignment 44
- Open the web interface 47
- Discover devices 48
- The Home page 49
- Ethernet IP settings 55
- WiFi IP settings 56
- WiFi LAN settings 56
- WiFi security settings 57
- WEP Keys 58
- DHCP server settings 60
- Network services settings 64
- Dynamic DNS update settings 67
- IP filtering settings 70
- IP forwarding settings 71
- IP Network Failover settings 74
- Socket tunnel settings 78
- General Security Settings 80
- Miscellaneous Settings 80
- Local Endpoint Type: 81
- VPN Mode: 81
- Identity settings 81
- Local Endpoint: 82
- Pre-Shared Key Settings 83
- ISAKMP Phase 1 Settings 84
- Cellular 86
- Data Network 86
- Internet 86
- Remote Site HQ 86
- IP pass-through settings 88
- Host List settings 91
- Advanced network settings 93
- Mobile (cellular) settings 99
- Mobile Settings 101
- 5 Provisioning complete 104
- SIM Selection settings 105
- GPS settings 106
- Advanced Settings 107
- Digi SureLink™ settings 109
- Update PRL settings 113
- Enable 116
- Password 116
- Notes for the table: 118
- Supported character set 119
- WiMAX settings 125
- Network Connection 126
- XBee network settings 127
- Basic Settings 129
- Device Status 129
- Device Operations 130
- Gateway firmware updates 132
- OTA firmware updates 133
- .EXT value in 139
- File type 139
- Serial port settings 141
- RealPort profile 142
- Console Management profile 142
- TCP Sockets profile 143
- When the TCP 143
- UDP Sockets profile 144
- Serial Bridge profile 144
- Local Configuration profile 144
- Modem Emulation profile 145
- Industrial Automation profile 145
- GPS Profile 145
- Custom Profile 145
- Basic serial settings 146
- Advanced serial settings 147
- Camera settings 150
- Alarm notification settings 151
- Alarm conditions 152
- Alarm configuration 153
- Enable and Disable Alarms 154
- System settings 155
- Authentication failure 161
- Cold start 161
- Link up 161
- Device Cloud settings 163
- Connection settings 164
- Mobile (Cellular) Settings: 169
- 4 Click Apply 171
- Users settings 172
- Caution 173
- Password authentication 174
- Add users 176
- User access settings 176
- User permissions settings 177
- 3 Click on User Permissions 178
- 5 Click Apply 178
- Position - GPS support 180
- Applications 182
- Digi device 184
- Digi device and click Delete 184
- RealPort Settings 187
- Ekahau Client™ 188
- Device Descriptors: 189
- Access the command line 191
- Monitoring and management 195
- Display system information 197
- Serial port information 198
- Network statistics 200
- ICMP statistics 202
- WiFi LAN statistics 203
- Device Cloud status 215
- Position/GPS statistics 215
- XBee Network 216
- Watchport Sensor statistics 218
- SureLink statistics 219
- Diagnostics 220
- Manage serial ports 221
- Manage connections 221
- Event logging 222
- Manage network services 223
- Device administration 230
- File management 231
- Secure Shell (SSH) Hostkeys 243
- Prerequisites 245
- Using the boot command 246
- Connector 247
- ConnectPort X4 H 248
- Reset button 248
- Reboot the Digi device 250
- Specifications and 252
- ConnectPort X2 specifications 253
- 4.5 in (11.4 cm) 254
- ConnectPort X4 specifications 255
- Hardware specifications 256
- Wireless networking features 257
- Infrastructure Mode 258
- Ad-Hoc Mode 258
- FCC Part 15 Class B 259
- ((( ))) 262
- ConnectPort X4 S2 2G Term 263
- ConnectPort X4 H 263
- Troubleshooting 265
- System status LEDs 266
- 1: signal strength low/weak 267
- ConnectPort X4 - Top 268
- ConnectPort X4 - Front panel 268
- ONNECT ORT 269
Relacionado con productos y manuales para Redes Digi ConnectPort X4
Redes Digi XPress Manual de usuario
(2 paginas)
(2 paginas)
Redes Digi XPress Manual de usuario
(8 paginas)
(8 paginas)
Redes Digi 34 Manual de usuario
(13 paginas)
(13 paginas)
Redes Digi CM Guía de usuario
(202 paginas)
(202 paginas)
Redes Digi SYNC/570i Manual de usuario
(54 paginas)
(54 paginas)
Redes Digi 34 Especificaciones
(148 paginas)
(148 paginas)
Redes Digi M10 Especificaciones
(38 paginas)
(38 paginas)
Redes Digi Digi One EM Guía de usuario
(43 paginas)
(43 paginas)
Redes Digi 9P 9360/9750 Guía de usuario
(75 paginas)
(75 paginas)
Redes Digi CM Manual de usuario
(1 paginas)
(1 paginas)
Redes Digi Rabbit 5000 Manual de usuario
(119 paginas)
(119 paginas)
Redes Digi LTS 32 Guía de usuario
(150 paginas)
(150 paginas)
Redes Digi ConnectPort X4 Manual de usuario
(37 paginas)
(37 paginas)
Redes Digi 9XTend-PKG-R RS-485 Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.401 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales